Low Profile IC Can Lighting

Features

MR-16, 20 watt Flood Light Bulb: Voltage: 12 Wattage: 20 Spread: 36 degrees
RECESS HOUSING Refer to photo diagram to the right. A - OUTER HOUSING - Die-formed steel construction for maximum heat dissipating air chamber on top of the housing. B - INNER HOUSING - Deep-drawn single piece aluminum construction for maximum heat dissipation and rust protection. C - TRANSFORMER - Class H electronic transformer with enhanced heat dissipating cover attached to junction box cover. Transformer can be reached from inside housing. D - BAR HANGERS - Pre-installed bar hangers allow the housing to be positioned and locked at any point within a 24” joist span. They are designed to be hammered directly without using nails or screws and could be fit onto T-bar spline for easy installation and quick alignment. E - JUNCTION BOX - Is ETL listed for through- branch circuit wiring and has 3 - 1/2” KO’s.

Specs

Adjustable Gimbal Ring:

• Available in 3 finishes: Polished Brass, Chrome & Satin.
• Holds up to a maximum 50 watt, MR-16 bulb.
• 3 5/8” Diameter, 2” deep.
• The trim can be regressed or out-gressed for a 35 degree tilt.
• Can take up to 2 optical accessories.
• Aluminum die-cast construction with a polished brass finish.
• Internal gasket prevents 100% of all light leakage. 2” Miniature Low Voltage Noise Free IC Housing:
• A light that can be used for both ceiling and soffit applications.
• Designed for New Construction, to be used in conjunction with insulation.
• These can be used for Remodel Construction as long as they have the ability to run the proper electrical and have access to the ceiling joists.
• 5 ½” height allows for use in joist construction.
• Small aperture, low voltage specification grade housing.
• Integral low voltage electronic transformer to prolong lamp life and increase lighting quality.
• Thermally protected IC rated Housing.
• Designed for accent and task lighting applications.
• Pre-installed adjustable bar hanger.
• The housing unit can be installed between or below joists.
• For below-joist installation, it may be necessary to drop the ceiling – If the ceiling does indeed need to be dropped, it MUST BE NOTED on the Design Request Form!
• 4 ½” KO’s on junction box.

Design

Free Design Services

Do you have a room or a designated space that you would like to transform into a wine cellar, wine storage area, or wine room?

Click design request, & share your room dimensions with us, along with some other valuable information pertaining to your wine storage needs, and we will provide you with a wine storage plan layout free of charge.

We can design a room or area for you with either our modular wine rack kits, or our custom products. We can design by budget, bottle capacity, or any other criteria.

Shipping

The average lead time is 4 weeks. If you are also ordering wine racking, we will attempt to ship out your lighting with your wine racking shipment.

Finishes

Policies

Cellar “Lighting” includes IC Can Ceiling lights, Halogen Recessed lights, LED lights and Fluorescent Slimlites. Missing Parts Upon receipt of your lighting you will have up to 3 weeks to review the shipment and inventory all of the parts. If you note any missing parts you can contact your design consultant and request a free replacement. If you contact us after 3 weeks, but before the end of the 4 weeks from delivery of your lights, you will be charged 15% of the cost of that replacement part. If you contact us after 4 weeks, but before 6 weeks you will be charged 25% of the cost of that replacement part. Any requests after 6 weeks and you will be charged the full amount for the replacement item. Dysfunctional Lights If, upon installation of the lights, they are not working properly, you must check all connections, polarities, and outlets, prior to requesting a replacement. If the issue is with LED lights, then you must exhaust all suggestions on the LED Installation Trouble Shooting Guide, prior to requesting a replacement. You can contact your design consultant and request a free replacement. Return Policy Upon receipt of your lighting you will have 6 weeks to review the shipment and inventory all of the parts. If you note any missing parts you can contact your design consultant and request a free replacement. If you contact us after 6 weeks you will be charged 50% of the cost of that replacement part. Any requests submitted after 12 weeks you will be charged the full amount for the replacement item. If you need to return your lighting for any reason other than missing on dysfunctional parts, you may do so within 30 days upon receipt of the order. You can return the lights and corresponding parts, in a like new condition, for a 15% restocking fee and the original shipping charges out, plus the return shipping charges. The products must be returned in the original shipping container they were sent out in. Any damaged parts that are not caused due to shipping damages will be deducted from your refund as well, whether the damage was caused by you or the person installing the lighting on your behalf. If there is shipping damage due to insufficient packaging that was provided by you, that amount will be deducted as well. All items must be returned in the original packaging with all parts intact. You must call your design consultant and request an RMA (Return Merchandise Authorization) number before returning your unit.